Pop-lock PL8660 Manuel d'utilisateur télécharger pdf

Installation Instructions

Tailgate Lock

PL8660 series

Honda Ridgeline

2005 and Up

With or Without

Backup Camera

Package Contents: Lock Bezel, 2 keys, Mounting Bracket,

Locking Bolt Linkage, Crank Linkage,

2 Screws #8-32 x 1 1/2", 1 Bolt 1/4" x 2”

Locking Bolt Linkage and Slide Bolt

Long and Short Wire Harness, Zip Ties

Tools Required: 10 MM Socket, T40 Torx Bit, Phillip Head

5/32” Allen Wrench

Rubber Mallet

Power Drill

3/16” (or 5MM), 1/2" (or 12MM) Drill Bits

STEP 1 - Lower the tailgate. Remove the four Phillips head screws from the top trim, slide the

trim

to the right (passenger) side using a rubber mallet and lift to remove it. Apply downward

pressure on

the top trim if it bows up. Remove the white clips that remain on the tailgate by

turning them 45

degrees to pull out. NOTE THE ORIENTATION BEFORE REMOVEL.

Remove the T40 torx

screws holding the interior trim panel and lift it off.

STEP 2 - Remove the handle rod from mechanicals by turning the green rod clip and

pulling the rod out of the clip. Swing the rod up and out of the way. Remove the two

screws holding the factory handle in place; there are tabs that will hold the handle

from falling out of the tailgate, but for extra assurance hold the handle in place so not

let the handle to fall. Install the mounting bracket over the back side of the handle and

reinstall the two screws and tighten. You may need to file the washer down go get the

bolt to fit. Reinstall the handle rod. The handle should now look like picture.

STEP 3 – Using the bracket holes as a template drill the two 3/16” (or 5MM) holes

and one 1/2" (or 12MM) hole. Insert the lock assembly from the front of the bezel

inserting the shaft through the 1/2" hole and aligning the two mounting holes on the

bezel with the mounting bracket. Insert the 2 supplied 8-32 x 1 1/2" screws

through the mounting bracket in the bezel. Tighten the screws. DO NOT OVER

TIGHTEN. IF LOCK ASSEMBLY BINDS LOOSEN SCREWS UNTIL THE

KEY MOVES FREELY!

STEP 4 – Remove the two mechanical assemble screws. Mount the POP N LOCK

bolt linkage under the upper latch rod as shown using the existing two mechanical

assemble screws. The lock assembly should look like picture.

STEP 6 – Check the functioning of the lock.

Technical Support:

Call 1-800-342-5911

technicalsupport@popandlock.net

STEP 5 – Install the crank rod assembly by holing the slotted end onto the bolt linkage and the

square hole to the end of the lock assembly shaft. Insert the 1/4" x 20 x 2” screw into the shaft and

tighten.

Lock – Turn the key to the right (passenger side) to the

two o’clock position and then back to 12 o’clock to lock.

Unlock – Turning the key to the left (driver side) to the

ten o’clock position and then back to 12 o’clock to

unlock.

For instructions in color please visit

our website at popandlock.net

1 2 3

Résumé du contenu

Page 1 - PL8660 series

Installation Instructions Tailgate Lock PL8660 series Honda Ridgeline 2005 and Up With or Without Backup Camera Package

Page 2

Technical Support: Call 1-800-342-5911 [email protected] STEP 7 – Remove the driver side lower mechanical

Page 3

POP & LOCKTM LIMITED WARRANTY FORM Please complete and mail this form to record your warranty with the manufacturer. LIMITED WARRANTY TERMS A

Commentaires sur ces manuels

Pas de commentaire

Pop-lock PL8660 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Pop-lock PL8660. Pop & Lock PL8660 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Pop-lock PL8660